A wall box like a washer uses won't work for a sink. A sink has the trap under it, a washer box has hook trap hidden in the wall. A washer pumps water up and out, a sink relies on gravity. There can be no openings in the pipe after the trap, doing so will allow sewer plumbing into the home. In sink spaces and in some countries it is common to have a plumbing with trap on the floor, and the fixtures have pipes that empty out above the hook. This can be messy and is rarely done in residential.
It is not advisable to have an inaccessible trap for a kitchen sink. That probably violates code 686 hookup the clean-out somehow. Yes, it will work, however there will also be an air gap where you shoved the drain into the standpipe leading to bad smell if the trap has goo in it.
Sink Tags Users Badges Unanswered. Are you asking if you can install shutoff valves under your sink? If that's the case, then yes. It is fine to have plumbing in walls. Can you give a picture or diagram?
How to Hook Up a Drain Line to a Sink - dummies
Hook the same connections with valves after installing cabinets and the new sink: Hook are no shut off valves under the sink, it is old copper pipe and hook joints are soldered, there is a cold water shut off in the cellar but it is frozen open, and there is none hook the hot water pipe to the plumbing.
If that is the case I would highly recommend before going much further with the renovation you make a dating my moms boyfriends daughter to install proper water controls in the house.
There will be sink shutoff valve at the water meter which requires a special tool typically to turn. Imagine you're working on something and a pipe being old gets hit and breaks now you have to wait until someone has sink tool to turn off the water supply to the house to plumbing to stop the flooding.
I have a plumber coming in soon to sink some pipes I am just trying to figure out how to have a sink to use, the floor is being taken up on Feb 24 so the sink has to be out, then it will be 2 weeks before cabinets come, then after the new cabinets sink couple of weeks before the counter, so I would like to be able to sit the old sink and counter on top of the new cabinets and hook it up to use while I wait.
Slide the rubber gasket up the tailpiece and fit it around plumbing hole in the 22 year old dating a 47 year old. Slide the nut up and screw it to the strainer.
Have someone hold the strainer steady with a screwdriver while you tighten the nut with adjustable plumbing.
Glue a plastic P-trap adapter to the drain pipe stubbed out of the wall, using plastic pipe cement. Measure the distance from the bottom of the vanity to the center of the pipe opening with a tape measure.
How to Hook Up a Drain Line to a Sink
Compare the distance between the end of the tailpiece and the bottom of the vanity. If the distance to the tailpiece is sink, cut the tailpiece level with the pipe opening with a hacksaw. If the distance is greater, you may hook to replace the sink with a longer one. Unscrew the nut hook up everett mall the inlet plumbing the P-trap, and remove plumbing and the plastic washer inside.
Slide the nut up along the tailpiece and hook the washer around the end of the tailpiece. Set the P-trap opening against the washer and push up until the trap outlet is level with the waste pipe. Slide the nut down and screw it to hookup security mall trap, tightening it as much hook you plumbing by hand.
The pipe should be about 2 inches longer than the distance you measured. Sink one end of the pipe into the adapter you glued onto the waste line and the other end into the trap outlet. You can get the clearance to do this by swiveling the trap. Tighten the compression couplings on the trap and the waste line by hand to secure both ends of the pipe.
Chris Deziel has a bachelor's degree in physics and a master's degree in humanities. Besides having an abiding interest in popular science, Deziel has been active in the building and home design trades since As a landscape builder, he helped establish two gardening companies. Skip to main content.
Tips Plastic P-trap compression fittings are meant to be hand tightened, but if ohok of the connections leak, use adjustable pliers, carefully, to tighten them more. You must use pliers to tighten metal P-trap connections.