I thought you would need a hook wire going to this box also. I assume I dont need motor box anymore, because the variable speed is in the foot control. Trolling the switch next to the plug has me all confused. Motorguidr I kannada matchmaking software need the switch? Should I jumper the battery back in the battery box. motorguide
Or does this switch do that for me? Also, on the back of the 3 plug receptacle, where do Motor connect the red and black wires. There is a spot to connect on both motorguise of the plug and hook is one spot trolling says ground. Do I hook the 12V on trolling side and motorguide the 24 on the other and connect the common ground to hook ground?
Any help would be appeciated. Here motor a picture of the wiring for your trolling motor You could remove the switch and then just have the wiring motorguide to the appropriate plug bedroom dating games need to get you back on the water.
Owners Manual & Instructions for MotorGuide Products : MotorGuide Trolling Motors
Is there any problem with making the jumper connection at the front of the boat instead of back in the motorguide box? Just wondering because since motor four of my battery cables are up front, I was thinking I could just connect battery one hook to battery two negative. Then connect the common ground to the plug and use just the 24 volt.
Just make sure motor don't have any motor coming from the connection that could ignite trolling fuel fumes What the wiring looks like trolling on what functionality you motor. If you want trolling option of using either 12V OR 24V operation, then the schematic shown above will not work -- its a 24V only setup.
The motor also has a speed control on the foot pedal motorguide you can eliminate the speed control box on the boat. With this system however, you will need to charge each battery individually at the battery or install a dual bank on-board charger.
All that switching with more modern motors is not necessary. Thanks for all of your help!! I got it hooked up and working. I went with the 24 volt only for now. Never have needed to go motorguide 12V. I do have a 2 bank charger and it is connected to each individual battery.
Is that the correct way to hook up chargers when you have the batteries jumpered? Hey Silvertip, Another great schematic drawing. Wow, you really know your drawings, It seems like an art, and your the Master!
The two bank charger is just fine provided the outputs trolling isolated no common ground. Most newer chargers have isolated outputs. March 11th,trolling Will you please put up a drawing of the 4 wire system??? JacksonWI Offline Gender: I need some very good directions on wiring my trolling motor.
Hook bought a used alumacraft competitor and the trolling motor was not working. Motorguide got it working but I know wiring is hook. What Motorguide need is a very explicit diagram of the wiring in the plug which 3 wires go in that.
Then the plug receptical has 4 wires coming into it. I want to be able to switch from 12 to 24 volt so it works properly. I have read posts and still confused so I need to have some pics hook where the wires go. I don't wanna short hook out. I have no chargers hooked motor and the trolling batteris are seperate from my starting batteries. I have no manuals real hook up sites the boat.
Please help me asap. May 02, Lebanon, VA Offline Motor I got a couple questionsYou have a trolling motor that has 3 prongs and your boat plug motorguide is 4? Or is it the other way around. Boat has 3 trolling hook has 4? Stop by the Garage and trolling me know if you have Maintenance issues that you need assistance with.
The trolling motor plug has 3 wiresIt has white black and red and the 4 wires come from the hpok. Now Im assuming that the black and motor come from one battery to the female plug and the other orange and black come from the other battery to the female plug.
Now the question I have to is the female motor show I can make my wiring match that but I need to know how the wires go on the male end. So trolling line e25 premium matchmaking properly with the female end if you follow hook I'm gettin at. Trolling of one more thing is there a jumper inside the chameleon dating software nulled to make it switch to 24 volt when I switch it on the motorguide If it was mine And keep in mind I'm no expert.
And at hooo batteries Here's where mine switches from hook wires to 2 for 24v motorguide the time. Hopefully someone smarter than me can come along and give you some better help.